Summary of common problems of faucet and solutions (Part 1)

1. The faucet in the home leaks, how to do?

2. Basin faucet water is very slow, faucet water is getting smaller and smaller, how to solve?

3. How to solve the problem that the faucet is not installed correctly?

4. What's wrong with the faucet and shower?

5. How does bathtub faucet change-over switch malfunction to return a responsibility?

6. The handle does not rotate smoothly. What should I do?

7. The valve rod is broken by accident. What should I do?

8. Can induction faucet only be single temperature?

Summary of common problems of faucet and solutions (Part 1)

There are faucets in the kitchen, bathroom and balcony. If there is a problem with the faucet, it will bring a lot of inconvenience to our home life, but we don't know what the reason is and how to solve it.

1. The faucet in the home leaks, how to do?

Most people think that the faucet leakage is that the valve core has a problem. In fact, as long as it is used properly, the valve core is not easy to have problems. Therefore, if the faucet leaks, it should be analyzed from its essence.

First. After the valve core is closed, the tap still has water. This phenomenon may be caused by the loose pressure cap of the valve core, which can not seal the water. The solution is to take down the handle and decorative cover and tighten the pressure cap again. There is another possibility that the rubber ring at the bottom of the valve core is deformed and unable to seal water. The solution is to take out the valve core, check the rubber ring at the bottom, reset it and then re install it.

Second. Water seeps from around the spool. This phenomenon may be the valve core loose or displacement, the solution is to take out the valve core and re install

Third. Water seeps from the middle of the valve core. This phenomenon is the valve core damage, the solution is to replace the valve core, if a tap water leakage on the replacement of the valve core, which will increase the maintenance costs.

Fourth. The bottom of the tap is leaking. This phenomenon is generally caused by the water inlet pipe O-ring is not installed or deformed. The solution is to screw out the hose. If the O-ring is found not to be deformed, the O-ring and the water inlet pipe can be re installed. If the O-ring is found to be deformed, replace the O-ring.

2. Basin faucet water is very slow, faucet water is getting smaller and smaller, how to solve?

First.  Look at the adjacent tap water is also very small, if it is also very small, is the problem of tap water pressure. If the water pressure is insufficient, it is suggested to add an electric water pump.

Second. If the water channel is blocked or the bubbler is blocked, if there is rust or impurities, the valve core can be removed and the water passage can be washed again; if only the bubbler is blocked, remove the bubbler and clean it again.

Third. If the water is slow, the sewer may be blocked and dredged by using dredger or physical negative pressure; or it may be that the sewer is too thin and does not match.

3. How to solve the problem that the faucet is not installed correctly?

In the process of installation, you should first put the faucet on the joint of the inner silk without winding the raw material belt to see if there is any problem with the inner silk on the street. If the tap is installed straight, then remove it and rewind the raw material belt again. Do not covet too much. After winding, press and smooth the raw material belt by hand and straighten it.

4. What's wrong with the faucet and shower?

This is caused by impurities blocking the filter screen. It can be solved by removing the filter screen and cleaning the impurities.

5. How does bathtub faucet change-over switch malfunction to return a responsibility?

First, it may be due to the water pressure. If the water pressure is too small, the change-over switch may not bounce when it is pressed down. If the water pressure is too high, the change-over switch may not be pressed down. Second, there may be impurities stuck in the switch and the switch can be removed for cleaning.

6. The handle does not rotate smoothly. What should I do?

The valve core is jammed. This phenomenon is that the impurities in the flowing water jam the valve core, which makes the valve core not rotate properly, and even damages the valve core. The solution is to clean up the impurities in the valve core; if the valve core is damaged, the valve core should be replaced.

7. The valve rod is broken by accident. What should I do?

This is basically the use of excessive force, or improper operation caused, only to replace the spool. When used correctly, the opening angle should not exceed 23 ° and the rotation range should be within 110 ° range.

8. Can induction faucet only be single temperature?

No, the induction faucet also has hot and cold water outlet, which can also be humanized to adjust the outlet water temperature.